> 1 <
ผู้เขียน | ข้อความ |
aobaobaut#5404![]()
203 โพส |
#391306 2013-09-09 21:29 GMT+07 ชั่วโมง |
เริ่มด้วยความอยากจะติดสัญลักษณ์ ///M 3 กับคนอื่นเค้าบ้างครับ ถึงแม้รถเราจะ 4 สูบแต่ก็มีความหลงไหลในสัญญลักษณ์ M ที่ติดอยู่บนบั้นท้ายเหลือเกิน จนหามาไว้ในครอบครองแต่ก็เป็นของมือสองจากหัวตัดครับ ใจก็กลัวจะติดไม่ถูกตำแหน่งสูงไปต่ำไปบ้าง ตอนแรกก็ติดแกะแล้วแกะอีกจนในที่สุดลองหาข้อมูลดู ปรากฎว่ามีด้วย เลยเอามาแบ่งปันกันครับ หากเพื่อนพี่ๆรู้แล้วก็ขออภัยด้วยนะครับ ลองดูรูปแล้วทำตามครับไม่ยาก
อุปกรณ์ก็ง่ายๆ ได้แก่ - สัญลักษณ์ ///M 3 - กาวสองหน้า 3M แบบบางสีเทาๆ ติดและตัดแต่งตามมุมตามสะดวกครับ - เทปกาวกระดาษแบบเขียนได้ - ไม้บรรทัด - ปากกา - ตัววัดพื้น (ผมไม่ได้ใช้ครับลองกะเอาเอง) งั้นเรามาเริ่มทำตามเค้าเลยแล้วกันครับ ขอโทษที่ไม่ได้ถ่ายรูปตอนทำนะครับ เพราะเหมือนในรูปเค้าเลย ถ่ายแต่ตอนติดเสร็จแล้วครับ I've never seen a writeup on this here, so I figured i'd post the necessary information and throw some pics up to aid anyone who might be doing this in the future. Emblem part numbers are as follows (and they're not cheap, plan on nearly $50 for both pieces): "///M": BMW PN 51142250811 "3": BMW PN 51142250539 Here are the specs for placement: ![]() What you will need: -The specs for placement -A ruler that measures in mm -A level -Some painters tape -A writing implement with a fine tip -T square (not pictured, sorry) Also recommended: -Some rubbing alcohol, clay bar, and microfiber towels...or whatever else you need in order to make sure you have a nice clean paint surface that's free of wax or contaminants. ![]() STEP 1: After cleaning the area completely, mark off A and B. I had the car parked on level ground and used the level to approximate the junction of A and B which is a critical point to measure accurately. I used the level to make sure that line A (height) wasn't crooked. Yes, I know it looks crooked...the dead straight line is under the piece of tape you see in the picture. You could also use the T-square to make sure this line is perpendicular to the lower edge of the trunk, but seeing as the metal is rounded I found using the level easier, and it's definitely close enough if the car is on level ground. After you have the height reference, you'll want to put a horizontal piece of tape that's parallel with the bottom of the edge of the trunk before it starts to round down. Don't use the level for this, as the line isn't completely level. I measured the height out off the edge of the trunk in 3 places and used that to place my horizontal line. This would serve as the horizontal reference for the emblem pieces. ![]() STEP 2: Using the t-square, place a vertical piece so you can square the '3' up real nice. This isn't 100% necessary, but I liked being able to literally butt the emblems up against the tape so the fitment was nice and accurate. Note that the bottom of the '3' is rounded, so it's possible to put that on crooked without a nice tight vertical reference for the side of it. ![]() STEP 3: Mark out C and place the ///M on the car. ![]() ![]() Now, peel off the tape and see how she looks... ![]() ![]() Success. ที่มาครับ : http://www.m3forum.net/m3forum/showthread.php?t=327603 สำเร็จแล้วครับสวยไปอีกแบบ ![]() ![]() โพสนี้ถูกแก้ไขโดย aobaobaut (2013-09-16 18:09 GMT+07 ชั่วโมง, ago) |
|
tewakul#3695![]()
234 โพส |
#391929 2013-09-15 23:37 GMT+07 ชั่วโมง |
![]() |
|
ZeesZaa#3246![]()
971 โพส |
#391975 2013-09-16 16:25 GMT+07 ชั่วโมง |
![]() ![]() ![]() ![]() ![]() |
|
oilers#653![]()
442 โพส |
#391982 2013-09-16 18:08 GMT+07 ชั่วโมง |
![]() ![]() ![]() |
|
A man of honor should pay his debt and keep his word
|
|
khumphol#803
1721 โพส |
#391994 2013-09-16 21:38 GMT+07 ชั่วโมง |
![]() ![]() ![]() |
|
รักนะ BMW เนี่ย...
|
|
pomSALVO#5168![]()
261 โพส |
#392854 2013-09-26 13:44 GMT+07 ชั่วโมง |
![]() |
|
> 1 <